Hey.
Just upgraded my cooler from noctua redux to deepcool ls720 SE AIO for my 13600k and installed thermal right contact frame. But the temperature in cinebench still somehow hitting 100°C.
I haven’t touched anything in bios except xmp.
Room temperature 32°C
Idle temps went from 45°C to 38°C
Gaming temps (mainly cs2) went from around 70-85°C to 55-70°C
Back with the air cooler I was getting lower and lower Score each run of cinebench but now the lower I get even after several runs never below 23k mark and the first run score got boosted by around 1000 point even though the CPU is hitting 100°C.
Here is a screenshot with the current temps am getting in the middle of running cinebench.
System specs:
Rtx 2070 super 13600k 2x8 ddr4 3600mhz Asus tuf b760m gaming plus d4
Running the AIO front mount with fans as intake and 3 top fans as exhaust and 1 back fan as exhaust.
So are those behavior normal during gaming and cinebench?
You must log in or register to comment.
Undervolt your CPU slightly and play around the load line calibration value. A -0.05v undervolt with the LLC at 2-3 should drop your temperatures quite a bit
No!
You NEED to touch bios settings on 13th / 14th gen!
This CPU won’t even last a year without degrading if left like that.
The motherboard bioses overvolt these chips for worst case scenarios.
Start off with forcing the stock power limit of the chip, I believe its 180w for the 13600K, actual usage in normal use shouldn’t be much higher than 140w.
Next calibrate the AC_LL, for some boards the value will read like 0.04, on others 40 for the same. The 13600KF I had worked at minimum AC_LL, yours might not.
Start with 0.04 then work down by 0.01 at a time and check it is still boosting in cinebench.
Also get HWinfo64 not HWmonitor.
what about DC_LL?
217W package power means that your cpu is overvolted by motherboard
Normal power usage for stock 5.1ghz 13600k in CB23 is 150-160wlooking like this is MSi board
It’s an Asus tuf b760m. So what do you suggest force power limits to default tdp or undervolt or both ?
So NR200P Max here with 13600k & b760-i bios 1205
The microcode settings is under F7 Advanced Mode -> TAB: AI Tweaker -> select Tweakers Paradies -> Switch Microcode
There you can select 0x104 Microcode
What i also changed is under AI Tweaker the following two selections:
Global Core SVID Voltage from Auto to Offset Mode
• Offset Mode Sign: -
• Offset Voltage: 0.15000
Cache SVID Voltage from Auto to Offset Mode
• Offset Mode Sign: -
• Offset Voltage: 0.15000
Cinebench 24100 pts ~ 152 Watt ~ 82 (few cores hit the max Temp of 89/90)
Hope i could help you guys out
Cant undervolt (much) in b series boards since it leads to performance degradation due to IA CEP. You need a z series board for that. Best you can do is lower pl1,pl2 to ~181w. Could try a bit less and see where performance starts to drop.
you should show what core voltage under load in Hwinfo64 or aida64
and 10sec of AIDA FPU to show power usage
i get those temps with a AK620 air cooler and my 13900K at 250w… well yeah im using AC to cool my room to 26°C but still…
When seeing posts like this, im getting scared of buying 13600kf/14600kf and putting it in my tuf b660m board
TDP of the 13600k is 181W, this while TDP of the 14600k is only 125W.
Main reason i got the 14 in my build
They both have a Base Power of 125W with a max boost power of 181W
Limit CPU Power Package 👍 Improved temperature
I had a worse AIO than you and my 12900K at 300W managed to just hit 100°C.
Your cooler is not doing its job.
First of all, use good thermal paste like Kryonaut or Thermalright TFX, and use a Thermalright LGA 1700 contact frame.
Second of all, ensure your AIO works and double check all connections.
Third of all, use HWiNFO64.
Cpu is obviously set to draw power until it throttles so not sure what you were expecting to see there aside higher cpu core frequencies maybe.
Room temperature 32°C
damm bro