I’m not sure if both have a separate audio board. I’ll try with my Senfer DT6 as well, those are great and relatively cheap. I also have some other in-ears and headphones, to confirm that the impedance is the important factor.

I’ve tested a few pairs of earphones and a pair of headphones (Very noisy: Sennheiser IE80, no noise: Philips Fidelio X2HR, Phonak Audeo PFE 112) and it looks like ones with 16 Ohms impedance exhibit a lot of noise, while 30 Ohms and up ones are silent.

I expect all of them to have the awful static on the headphone output. I sounds exactly like there’s a common ground between the system and audio hardware. I have this exact same problem with other hardware, it is a design fault.

For storage devices to work properly you need to change a setting in the BIOS. I don’t remember which setting exactly, but if you do a search in this subreddit it will probably turn up.

I don’t expect you could swap out the boards, a lot of the components have changed.

I’m quite sure this isn’t a software problem. My official Sony PSOne display and MiSTer FPGA have the same noise and it is caused by the grounding problem I mentioned.

Should it be the headphone wires inside picking up the noise, a shielded cable might fix it. But I don’t expect that to be the cause of the problem.

I just checked and I have the same thing on my 512GB OLED. This is a hardware bug. Sounds like system and audio grounding haven’t been properly separated.

It sounds quite bad, makes me wonder how this made it past QC.

One, not really acceptable solution, is to use a USB-C to headphone adapter. I just tried the cheap Apple one and it works perfectly. My Zorloo Ztella also works. My passive OnePlus cable doesn’t work, unsurprisingly.

Downside of that workaround is that the adapter will consume a little bit extra power.

Great to know, thanks! I will try that.

Works:

Pinball FX

Crysis Remastered

Horizon Zero Dawn

Spiderman

Cyberpunk 2077

Ori and the will of the whisps

​

Doesn’t work:

Control (thought this one was supposed to work?)

Pinball Arcade

NFS Unbound

Redout

Nex Machina

Hot Wheels Unleashed

Black Widow Recharged

Gravel

Star Wars: Squadrons

Inside

​

Grip, haven’t gotten it to work yet myself, look here: https://steamcommunity.com/app/396900/discussions/0/1652169858536175563/#c1644295067080498033

Mentioned files are here:

home/deck/.local/share/system/Steam/steamapps/compatdata/396900/pfx/drive_c/users/steamuser/AppData/Local/Grip/Saved/Config/WindowsNoEditor/

These are Unreal Engine settings, so it might work for other Unreal-based games, or you could borrow well working settings from other Unreal games.

Mentioned settings might not be perfect for the Deck, I don’t know if the exact HDR standards the Deck is using can be found anywhere yet.

I hope that all the OLED Decks out there will help increase HDR support in games. It can look really great when implemented correctly.

Sadly it only shows a small portion of the games that support HDR in my library.

And have much better battery life in the future. The last bit 10 to 20 percent of charging wears out your battery the most.

There’s a reason demo phones in stores are set to automatically charge between 30 and 80 percent.

When I have my Deck docked, I don’t want it to charge to 100% every time, wearing the battery out. When I’m planning on taking it with me, I charge it to 100%.

Use Decky Power Tools to limit charging in stand-by mode to 80%.

It is also something you get used to. My PC monitors are glossy and it annoyed me initially, now I don’t notice it anymore. Haven’t noticed it on my Steam Deck either.

I’ve just tried that for you and yes it works really well. Just shows all the extra games as installed. Tried one game and had to accept the eula again, but it works fine.

Pinball FX is great with HDR on the Deck. And you can try it for free. All the lights on the playfield look great and the 90 fps helps a lot to be able to follow the ball.

My 512GB arrived at 12 pm (Netherlands) I was able to quickly retrieve it from a pick-up point. Then finish my presentation and head out to work. Hopefully I will be able to try it out at 10 pm when I’ve returned from my work meeting. Can’t wait.

I’ve just received my timeslot in the Netherlands, from GLS, for tomorrow morning/early afternoon! (my order went through after 22 minutes of trying).

Too bad I have a work event later that afternoon and in the evening and also four meetings during the day.

Netherlands: Status went to shipped twenty minutes ago. Estimated to arrive tomorrow.

My 64GB from earlier this year already didn’t have that on the box. It still had a companion cube symbol, among the other warning symbols, on it though.